The Effect Of Feeding Motion Variation On Surface Quality In The Turning Process
Pengaruh Variasi Gerak Makan Terhadap Kualitas Permukaan Pada Proses Pembubutan
DOI:
https://doi.org/10.21070/yqpkyw54Keywords:
Feed rate, Surface quality, Turning process, Lathe machine, Surface roughnessAbstract
General Background: The turning process represents a fundamental machining operation widely applied in the manufacturing industry to produce cylindrical components with high dimensional accuracy. Specific Background: Feed rate variations during conventional lathe machining directly govern surface roughness and functional performance characteristics such as wear resistance and fatigue strength. Knowledge Gap: Prior investigations often evaluate generalized turning parameters without systematically correlating feed rate increments with quantitative surface roughness profiles across industrial steel components. Aims: This study aims to analyze the effect of feed rate variation on surface quality during the turning process using a conventional lathe machine at PT Anugrah Mas Gemilang. Results: Experimental evaluations demonstrate that increasing feed rates from 0.106 mm/rev to 0.319 mm/rev raises surface roughness values from 2.84 micrometers to 6.66 micrometers. Novelty: This work establishes a direct empirical relationship between feed rate increments and quantitative roughness profiles specific to general industrial turning operations. Implications: Implementing optimal feed rate selection strategies minimizes machining defects, improves surface finish uniformity, and elevates production efficiency for industrial component suppliers.
Key Findings Highlights
-
Demonstrating that increasing feed rates from 0.106 mm per revolution to 0.319 mm per revolution raises surface roughness from 2.84 micrometers to 6.66 micrometers,
-
Establishing feed rate as a dominant machining parameter that directly dictates cutting tool mark patterns and surface profile uniformity,
-
Providing practical parameters for PT Anugrah Mas Gemilang to optimize surface quality and minimize rework during conventional lathe operations.
Keywords Feed rate, Surface quality, Turning process, Lathe machine, Surface roughness
References
Zubaidi, I. Syafa, and Darmanto, “Terhadap Kekasaran Permukaan,” Momentum, vol. 8, no. 1, pp. 40–47, 2012.
D. Abimanyu and H. Nurdin, “Pengaruh Gerak Makan Dan Kecepatan Putaran Spindle Terhadap Tingkat Kekasaran Permukaan Aluminium Pada Proses Pembubutan Menggunakan Mesin Bubut Konvensional,” J. Multidisciplinary Res. Dev., vol. 1, no. 4, pp. 783–790, 2020.
Ninuk Jonoadji and Joni Dewanto, “Pengaruh Parameter Potong dan Geometri Pahat Terhadap Kekasaran Permukaan Pada Proses Bubut,” J. Tek. Mesin, vol. 1, no. 1, pp. 82–88, 1999. [Online]. Available: http://puslit2.petra.ac.id/ejournal/index.php/mes/article/view/15899
M. Darwis, R. Ramli, and R. Bernadipumar, “Pengaruh Ingsut Terhadap Kekasaran Permukaan Benda Kerja Pada Proses Pembubutan,” Cendekia J. Ilmu Pengetah., vol. 2, no. 2, pp. 150–156, 2022, doi: 10.51878/cendekia.v2i2.1152.
Y. M. Putra, G. E. Timuda, N. Darsono, N. Chollacoop, and D. S. Khaerudini, “Optimization of Machining Parameters on the Surface Roughness of Aluminum in CNC Turning Process Using Taguchi Method,” Int. J. Innov. Mech. Eng. Adv. Mater., vol. 5, no. 2, p. 56, 2023, doi: 10.22441/ijimeam.v5i2.21679.
H. Hadimi, “Pengaruh Perubahan Kecepatan Pemakanan Terhadap Kekasaran Permukaan Pada Proses Pembubutan,” J. Ilm. Semesta Tek., vol. 11, no. 1, pp. 18–28, 2008. [Online]. Available: https://journal.umy.ac.id/index.php/st/article/view/773
M. R. Reddy, “Effect Of Feed Rate On the Generation Of Surface Roughness In Turning,” Int. J. Eng. Sci. Technol., vol. 3, no. 11, pp. 8099–8105, 2011.
D. S. Nasution, M. R. Harahap, and A. H. Nasution, “Pengaruh Feeding Terhadap Kekasaran Permukaan Pada Pembubutan Baja AISI 1020 Dengan Menggunakan Mata Pahat Karbida Berlapis,” Piston, vol. 6, no. 1, pp. 19–25, 2021.
F. Manta, K. D. Artika, and G. Gunawan, “Analysis of Tool Wear and Surface Roughness in Turning ST41 by Insert Tool for Variation in Feed Rate,” Sebatik, vol. 29, no. 1, pp. 35–40, 2025, doi: 10.46984/sebatik.v29i1.2609.
R. Trisno et al., “Rate Mesin Bubut Terhadap Kekasaran,” J. Tek. Mesin, vol. 4, pp. 76–86, 2015.
S. Kalpakjian and S. R. Schmid, Manufacturing Engineering and Technology, 7th ed. Pearson, 2014.
M. P. Groover, Fundamentals of Modern Manufacturing: Materials, Processes, and Systems, 6th ed. Wiley, 2016.
D. A. Stephenson and J. S. Agapiou, Metal Cutting Theory and Practice, 3rd ed. CRC Press, 2016.
J. P. Davim, Machining Fundamentals and Recent Advances. Springer, 2008.
F. Klocke, Manufacturing Processes 1: Cutting. Springer, 2011.
Downloads
Published
Issue
Section
Categories
License
Copyright (c) 2026 Anggi Dwi Rahmadani, Mulyadi

This work is licensed under a Creative Commons Attribution 4.0 International License.
